![]() High zero fades are especially attention-grabbing because of how short the zero length really is. High fades are about as high as you can get with fades.Īny higher and you’d be going into high and tight territory. High Zero FadeĪ high zero fade is where the #0 length (0.5mm – 0.8mm) at the bottom of the sides and back starts to transition and blend into longer lengths around the level of the temples. In addition, the greater the difference in length between the zero length at the bottom of the sides and the hair on top of the head, the more eye-catching the zero fade will look.įor example, a mid zero fade will look more prominent when combined with a pompadour up top when compared to a #2 buzz cut with a mid zero fade. The greater the difference in length between the zero length at the bottom and the highest length it transitions to higher up the sides, the more obvious the shortness of the zero length will look. They aren’t as subtle as low zero fades or zero fade tapers.Īs with any other zero fades, the zero length can gradually transition into any longer length higher up – whether that’s a #1, #2, #3, or even longer. ![]() What this leads to is around half of the sides and back being at the shortest length – the very short stubble of the zero length.Īlthough this isn’t quite as short as a skin fade, it’s still super short.īecause of this, mid zero fades are pretty attention-grabbing and eye-catching. The exact height at which this occurs obviously depends on the individual’s head size.īut overall, the “one inch above the ear” guide is a pretty safe bet. Usually, this results in the zero length starting to blend into longer lengths approximately halfway up the sides. Mid Zero FadeĪ mid zero fade is where the #0 length (0.5mm – 0.8mm) at the bottom of the sides starts to transition into longer lengths approximately one inch above the ear. If you want a zero fade that’s noticeable but really just a minor feature of your overall style, a taper may be a good way to go. The transition from the zero length at the bottom into longer lengths further up the sides occurs around the top of the sideburns.Īs a result, zero fade tapers are about as subtle as you can get when it comes to zero fades. Low fades work well when it comes to that.Ī “zero fade taper” is essentially a very low zero fade. It’s a good option for men who want a very short fade at the sides but don’t want it to have too much prominence within their overall hairstyle. It’s a subtle form of a zero fade, simply because only a small portion of the sides and back is trimmed down to the shortest length – the zero length.Īs a result, a low zero fade isn’t as obvious or noticeable as mid fades and high fades, for instance. Low Zero FadeĪ low zero fade is where the zero length (0.5mm – 0.8mm) at the bottom of the sides starts to blend and transition into longer lengths approximately half an inch above the ear.Ī simpler way of saying it would be that the fade sits low on the sides and back. Let’s discuss these “fade heights” in more detail. They can be “low”, “mid”, or “high”, depending on how high up the sides the zero length reaches before it transitions into longer lengths. Zero fades vary according to how high up the sides and back they are. That blurred and faded effect is eye-catching. The characteristic “fade” effect is produced because the lengths blend into each other with no harsh lines. For example, from a zero at the bottom to a #0.5, #1, and then a #2 at the top of the sides. The clipper is then used to gradually increase the length in small increments, going up from the #0 length at the bottom. However, it won’t be as long as it would be if you were to attach a #0.5 guard or #1 guard, for instance. ![]() Leaving the lever open with no guard attached will allow you to get very slightly longer stubble. The lever of the clipper can be used to adjust the stubble length as well. The stubble length will usually be around 0.5 and 0.8mm when you use the clipper with no guard attached – it really depends on the blade height and the clipper you’re using.Ī standard Wahl blade will usually trim down to 0.8mm, while the #000 blade of an Oster or Andis clipper will trim down to approximately 0.5mm. ![]() It doesn’t require shaving – you don’t need a razor to produce it because you aren’t shaving all the way down to the skin.Ī clipper with no guard attached is used to produce the short stubble at the bottom of the sides and back. Notice the slight shadow left behindĮssentially, a zero fade haircut is one step longer than a skin fade.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |